Samsung Dryer Error Codes: tC, tO, HC, dC and 9C1 Explained
The short answer: Samsung dryers show information codes instead of a warning light, and the letters name a system. tC and tO report a temperature-sensor problem that is usually caused by a clogged lint screen or a restricted vent, HC reports overheating from the same cause, dC is the door, 9C1 and 9C2 are about the power supply, and 5C is a drainage message on condensing and heat-pump models. Samsung lists these in its dryer error code guide, and the first step for almost all of them is the same: unplug the dryer, wait about 30 seconds, and try again.
In this guide
- How to read the code
- The code table
- tC, tO and the temperature family
- HC: overheating
- dC and the door family
- 9C1 and 9C2: power supply
- bE and the button family
- 5C: drainage on condensing and heat-pump dryers
- NC, NC2 and FIL + tEr: filter and heat exchanger
- 3C motor and AC6 communication
- FC and invalid power frequency
- Maintenance that prevents most of these
- Safety
- When to call Samsung service
- Frequently asked questions
How to read the code
Three things about Samsung dryer codes confuse owners, and each one matters:
- A code that looks like an upside-down F is a t. Samsung notes this explicitly. What reads as “⅂C” on the display is tC.
- Models without a digital display show codes as blinking lights. A pattern of flashes is the code, and the manual maps the pattern to the letters.
- The first step is universal. Unplug the dryer for at least 30 seconds, then plug it in again. That resets the control board and clears latched messages. A code that disappears and stays away was not a part failure.
Some codes carry a leading “1” on machines with two compartments, such as a Flex system where the upper and lower units report separately. If your dryer shows 1 tC or 1 dC, the message belongs to the numbered compartment, and the checks apply to that unit.
The code table
| Code group | Reported system | First check | Self-fixable? |
|---|---|---|---|
| tC, tO, tE (also tS, tC5, tCS) | Temperature or temperature-sensor problem | Lint screen, lint filter housing, vent restriction | Yes, for the airflow causes |
| HC, hE (also HC4) | Overheating or high-temperature cutoff | Lint screen, blocked vent, tripped breaker for the heat circuit | Yes, for the airflow causes |
| dC, dE, dF, d0 | Door | Door closed, nothing caught, child lock off | Yes |
| 9C1, 9C2 (also 9E1, 2E) | Voltage supply | Dedicated circuit, no extension cord, correct cord installation | Yes |
| bE, bE2 (also 6E) | Control-panel button stuck or held | Press each button to release it | Yes |
| 5C, 5E | Drainage, on condensing and heat-pump models | Water tank full, drain hose kinked or frozen | Yes |
| NC, NC1, NC2 | Lint filter, or heat-exchanger cover | Filter seated correctly; inner cover fitted properly | Yes |
| FIL + tEr (with buzzer) | Heat exchanger needs cleaning | Clean the heat exchanger | Yes |
| 3C, 3E | Motor (on some models 3E is voltage) | Restart the cycle once | Restart only |
| AC, AC6 | Communication between control boards | Restart once | Restart only |
| FC, FE | Invalid power source frequency | Restart; check the supply | Restart only |
tC, tO and the temperature family
tC and tO both report a problem with the air temperature sensor or with the temperature it is reading. Samsung’s own first instruction is not to replace the sensor but to clean the lint filter and the heat exchanger and to check whether the vent system is restricted. The reasoning is simple: a blocked exhaust traps heat in the cabinet, the sensor reads a temperature the control cannot explain, and the code appears. The sensor is the messenger.
Work through the airflow checks before anything else:
- Pull the lint screen and clean it properly. Peel the lint off, then use a soft brush and warm water occasionally to remove the film that soap and fabric softener leave behind.
- Look inside the filter housing with a torch. Lint past the screen forms a mat over the duct opening that many owners never see.
- Check the vent run behind the dryer — crushed, kinked, or coiled flexible duct is a restriction even when it looks connected.
- Check the outside hood with the dryer running; the flap should open fully and air should be obvious.
tC5 and tCS are versions of the same message on heat-pump models, where a compressor handles the heat. Samsung’s advice there is to wait two or three minutes, restore power, and start again, after checking for a clogged screen or restricted vent. tE3 and tS belong to the same family and are handled the same way.
HC: overheating
HC and hE mean the dryer detected overheating or a high-temperature condition, and Samsung’s list of causes is almost entirely about airflow and power. Clean the lint screen and the vent thoroughly. Then check the household breaker panel: on an electric dryer, a breaker that has tripped or a supply that is delivering low voltage can make the heater behave erratically, and Samsung notes that checking the heating-element wiring requires a licensed electrician.
An HC code deserves attention beyond clearing it. Overheating is the mechanism behind dryer fires, and NFPA’s analysis of 2014–2018 fires found that about a third of home dryer fires were caused by failure to clean. If HC appears, treat the vent as the problem until you have proven otherwise: clean it, and if the code returns on a clean vent, stop using the dryer and have it inspected.
dC and the door family
dC, dE, dF and d0 all describe the door or the switch that detects it. Close the door firmly and check the fold of the seal for a sock, a dryer sheet, or a small item. Check that the lint filter is fully seated — on many Samsung dryers a filter that is not pushed home keeps the door from closing flush.
If child lock is on, opening the door produces a door message even when the dryer is idle. Turn child lock off and try again. dF specifically means the door switch is reporting the wrong state, which points at the switch or its wiring rather than at how the door was closed; if dF returns after a power cycle, the switch needs service.
9C1 and 9C2: power supply
These are voltage codes. Samsung’s checks: confirm the dryer is on its own circuit and not using an extension cord; for an electric dryer, confirm the power cord is installed correctly and the correct voltage is being supplied; and note that a dryer moved to a country with a different supply can throw this code for that reason alone. 9C1 usually indicates an over-voltage condition and 9C2 an under-voltage condition.
One practical complication: on a stacked pair controlled by a multi-control kit, the washer can report a dryer 9C1 if you try to control the dryer within about five seconds of switching the washer on. That is a known behavior with a software fix, not a fault in the dryer. Wait a few seconds before touching the dryer controls.
bE and the button family
bE, bE2 and 6E report a control-panel button that is stuck or being read as continuously pressed. Power the dryer off, then press each button firmly a few times to release it. A spill or a build-up of cleaning product around the panel is a common cause. If a button feels dead or the code returns immediately, the panel needs service.
5C: drainage on condensing and heat-pump dryers
Not every Samsung dryer vents to the outside. Condensing and heat-pump models collect water in a tank or drain it through a hose, and 5C means that water is not leaving. Samsung’s checks: make sure the drain hose is not bent or damaged, thaw it if it has frozen by wrapping it in a towel soaked in warm water for about ten minutes, and empty the water tank before starting again. If the tank is full, the dryer cannot condense more moisture and the cycle stops.
Heat-pump dryers also have a heat exchanger that must be cleaned. If yours has a removable cover, check that the inner cover is refitted correctly after cleaning — a cover that is not seated produces NC2, and a dirty exchanger produces FIL + tEr with a buzzer.
NC, NC2 and FIL + tEr: filter and heat exchanger
NC and NC1 mean the dryer wants the lint filter checked: pull it out, clean it, and confirm it is seated in its slot. NC2 is about the inner cover of the heat exchanger on condensing models, which has to be fitted correctly for air to pass through the exchanger. FIL + tEr with a buzzer is a maintenance reminder: the heat exchanger itself needs cleaning. Clean it, refit it, and the message clears.
3C motor and AC6 communication
3C points at the inverter motor, and on some models 3E means the same while on others 3E is a voltage code — Samsung tells owners to check the manual for the specific model. Restart the cycle once. A 3C that returns with a light load means the motor or its drive needs service, and the dryer should not keep running.
AC, AC6 and AE6 report a communication problem between the main board and the inverter board. Restart once. If the code returns, the boards or their harness need service; there is nothing to clean or adjust.
FC and invalid power frequency
FC and FE mean the dryer sees a power source frequency it does not expect. This is almost always a supply or installation issue rather than an appliance fault — a generator, an inverter supply, or a dryer moved from a 50 Hz country to a 60 Hz one will produce it. Restart the cycle and check the supply; if the code persists on ordinary mains power, request service.
Maintenance that prevents most of these
- Clean the lint screen before or after every load. Wash it with warm water and a soft brush every few months and let it dry fully.
- Clean the vent run at least once a year, and more often with pets or a long duct.
- Verify the outside flap opens while the dryer runs, and clear lint from the hood.
- On heat-pump models, clean the heat exchanger as the FIL + tEr reminder appears, and empty the water tank every load or two.
- Leave space behind the dryer so the transition duct does not crush against the wall.
- Check the outside flap while the dryer runs, and clear lint from the hood each season.
Safety
- Unplug the dryer before removing panels, checking cords, or reaching behind the drum.
- Do not run a dryer that has reported HC or repeated temperature codes until the vent has been cleaned and inspected.
- Do not dry clothing that has been in contact with gasoline, paint thinner, cooking oil, or solvents.
- Do not leave the house or go to sleep with the dryer running.
- If you smell gas on a gas model, leave the building and call the gas utility; do not operate switches on the way out.
- Keep the floor area around the dryer clear of lint, paper, and stored items.
When to call Samsung service
Request service when a temperature or heating code returns after the lint screen and vent have been cleaned, when 9C1 or 9C2 appears on a dedicated circuit with the correct cord, when a door code returns with a clear seal and child lock off, when bE persists after freeing the buttons, or when 3C, AC6, FC or FE repeat after a restart. Those point to sensors, boards, switches, or the motor — parts that need a technician.
Frequently asked questions
What is the first thing to do when any Samsung dryer code appears?
Unplug the dryer, wait at least 30 seconds, and plug it back in. That is Samsung’s own first instruction and it clears latched messages without tools. If the code returns on the next cycle, move on to the system-specific checks.
Does tC mean the temperature sensor has failed?
Not necessarily. Samsung attributes tC and tO first to a clogged lint screen or a restricted vent, and says to clean those before contacting service. The sensor is reporting heat it cannot account for, and blocked airflow is the usual reason.
Why does my dryer show HC when the clothes are barely warm?
HC reports a high-temperature condition detected at the heater or a safety limit, which can happen before the drum feels hot to you — especially if the vent is partly blocked. Clean the lint screen and the vent, then check the breaker for the heat circuit.
Is 5C a fault on a vented dryer?
5C is a drainage code. On a condensing or heat-pump dryer it means the water tank is full or the drain hose is blocked or frozen. On a vented model you would not normally see it, so check your model type before troubleshooting a drain that does not exist.
How often should the heat exchanger be cleaned on a heat-pump dryer?
Follow the dryer’s own reminder — the FIL + tEr message with a buzzer is that reminder. In practice, most households clean the exchanger every few weeks to a couple of months, and always after the message appears, because a coated exchanger lengthens every cycle.
My code is not listed here. What now?
Check the manual for your exact model, or Samsung’s support page for your product family. The same letters can mean different things on different dryers, and Samsung itself flags 3E and dC as codes that vary by model.