Whirlpool Dishwasher Not Draining: The F9E1 Check Order
The short answer: When a Whirlpool dishwasher leaves water in the bottom, the cause is almost always a restriction somewhere along one path: filter → sump → drain pump → drain hose → air gap or garbage disposal → sink drain. Whirlpool publishes the checks in a sensible order — filter and sump first, then the hose and its high loop, then the disposal knockout plug and the air gap, then the pump — and most cases are solved by the first two. If the display shows F9E1, Whirlpool calls it a long drain: the machine ran the pump but could not clear the water in the expected time. One thing to know before you start: a small amount of water standing in the filter area — roughly halfway up the filter well — is normal, not a failure. It keeps the seals in that area from drying out and is replaced at the start of the next cycle.
This guide follows Whirlpool’s published drain troubleshooting, adds the practical notes that decide whether each step works, and marks clearly where we are interpreting rather than quoting. It applies to the WDT750SAKZ and to Whirlpool’s other built-in dishwasher lines; your filter may have one piece or two, so check your own owner’s manual for the layout.
In this guide
- Is it really not draining?
- How the drain path works
- Read the clue before you touch anything
- Step 1: safety and standing water
- Step 2: the filter and sump
- Step 3: the hose, high loop and air gap
- Step 4: the garbage disposal knockout plug
- Step 5: the pump
- F9E1 and the power cycle
- Prevention that actually works
- Safety notes
- Sources
- Frequently asked questions
Is it really not draining?
Whirlpool’s own guidance starts here, and it saves a lot of unnecessary work. Water in two places means two different things:
- Water in the filter well, about halfway up — normal. Whirlpool states plainly that this small amount of standing water is there to keep the seals from drying up, and that it drains at the start of the next cycle. If this is all you see, you do not have a drain problem.
- Water above the filter screen, in the tub floor, or up near the door opening — a real drain problem. The higher the water, the more complete the blockage or the more likely the pump is not running at all.
If the machine finishes a cycle with an inch of cloudy water across the bottom, run the diagnosis below in order. If it finishes dry but the filter well holds a cup of water, close the door and move on with your day.
How the drain path works
At the end of a wash or rinse, the control energises the drain pump. The pump pushes water out through the drain hose to one of three destinations: the sink drain, an air gap on the sink deck, or a garbage disposal. Two things must be true for that to work:
- The path must be open — no food in the filter, no debris in the sump, no kink or clog in the hose, no plug or blockage at the disposal or air gap.
- The path must be routed correctly — the hose needs a high loop, an arch secured high under the counter, or a working air gap. Without one, wastewater siphons back into the tub and you get a dishwasher that “did not drain” even though the pump ran fine.
Whirlpool lists the frequent causes in roughly that order: clogged filter, debris in the sump, kinked or blocked drain hose, a problem at the disposal or sink connection, or a jammed drain pump. Less commonly, a faulty timer, a drain solenoid on certain older designs, or the control board can interrupt the drain cycle.
Read the clue before you touch anything
The symptom narrows the search. This table is Whirlpool’s diagnostic-clue list, arranged by what you can see or hear.
| What you observe | Most likely area | Where to start |
|---|---|---|
| Water slightly above the filter screen | Partial restriction in filter, sump or hose | Step 2, then Step 3 |
| Water near the door opening | Severe blockage, or the pump is not running | Step 2 through Step 5 |
| Steady hum, no water movement | Jammed pump impeller | Step 5 after clearing the sump |
| Grinding noise during drain | Hard debris such as glass in the pump area | Step 2 carefully, then service |
| Cycle pauses and the drain pump never starts | Electrical or control issue | F9E1 section; power cycle, then service |
| Water backs up out of the air gap onto the sink | Blockage downstream of the air gap | Step 3, sink plumbing |
| Nothing happens at all, panel dead | Door latch or power, not the drain | Check the latch and breaker first |
Write down the two or three observations that match. They tell a technician more than “it doesn’t drain,” and they tell you when to stop taking things apart.
Step 1: safety and standing water
Before removing anything: turn the power off at the circuit breaker. Whirlpool states explicitly not to rely on the control panel, and to confirm the display and lights are off. Then shut off the water supply at the under-sink valve, typically the hot-water line feeding the dishwasher.
Have these within reach: absorbent towels and a small bucket or pan, pliers, Phillips and flat-head screwdrivers, a flashlight, gloves, a hand pump or turkey baster, and a shallow tray for catching water when a hose comes off.
Remove the standing water before inspecting anything. It makes the filter visible, prevents spills when you open the sump, and stops dirty water running into the cabinet when you disconnect a hose:
- Place towels in front of the dishwasher.
- Bail the tub water with a cup into a bucket.
- Use a turkey baster or hand pump for the sump — the recessed well around the filter.
Dispose of the wastewater down a sink or toilet. Do not pour drain-opening chemicals into the dishwasher: they attack the seals and pumps and create a hazard for whoever works on it next. This is one of the few places where a common household shortcut is actively destructive.
Step 2: the filter and sump
Whirlpool says many “clogged dishwasher” complaints start here, with neglected filters or food debris in the sump restricting flow. The cleaning routine:
- Remove the lower rack.
- Twist the upper (fine) filter counter-clockwise and lift it out.
- Lift out the lower (coarse) filter or mesh if your model has one — some models have a single assembly.
- Rinse both under warm water and use a soft brush to remove residue. Avoid abrasive pads; they damage the mesh and the damage is permanent.
- With the filters out, shine a flashlight into the sump. Remove food particles, produce labels, seeds, toothpicks and any glass. A sticky label that has wrapped around the pump inlet is a common and completely invisible cause.
Reassemble carefully: seat the lower filter flat, then lock the upper filter by turning it clockwise until fully engaged. Whirlpool warns that an improperly seated filter reduces wash performance and lets debris reach the pump — so a filter that was reinstalled crooked last month can be the entire cause of today’s no-drain.
Run a short rinse cycle with the machine empty. Listen for the drain pump and watch whether water remains. If it drains, stop here. If not, continue.
Step 3: the hose, high loop and air gap
Look under the sink and behind the toe panel. The drain hose must not be kinked, crushed or sagging into a trap of its own. And the routing matters as much as the condition:
- High loop: the hose should arch up and be secured near the top of the cabinet wall or the underside of the counter before it connects to the disposer or drain pipe. If it runs flat or downhill, pull the excess upward and secure it with a bracket or zip tie.
- Air gap: if one is installed on the sink deck, it should be clear inside and under its cap. Follow the air gap manufacturer’s instructions for removing the cap and clearing a blockage.
To check the hose for a clog:
- Put a towel and a shallow pan under the sink connection.
- Loosen the clamp and detach the hose from the garbage disposal or sink tailpiece.
- Check the hose end and the inlet for debris.
- Flush the hose with warm water from a faucet, or outdoors with a garden hose. For stubborn clogs use a flexible plastic line or a dishwasher-safe brush — never a sharp tool, which punctures the hose.
- Examine the sink tailpiece, trap and nearby plumbing for buildup. If the sink itself drains slowly, the dishwasher is trying to push water into a partly blocked drain.
Reattach the hose and tighten the clamp snugly without over-tightening, then restore the high loop. Run a short cycle. If water spills out of the air gap into the sink during the drain, the blockage is downstream — in the hose-to-drain path or the sink plumbing — rather than inside the dishwasher. That single observation can save a service call.
Step 4: the garbage disposal knockout plug
If the dishwasher drains into a disposal, and the disposal was recently installed or replaced, this is the first thing to check — and it is the most common new-installation cause of a dishwasher that will not drain at all. The disposal ships with a plastic plug in its dishwasher inlet. If nobody knocked it out, the drain path is sealed.
Whirlpool’s own field method for checking without removing the disposal: disconnect power, disconnect the drain hose from the disposal, catch the water in the hose, then insert a pencil into the inlet and feel for the plug. If the pencil goes in about three inches, the plug has been removed; if it stops short, the plug is still there.
Also check for food or obstructions caught in the drain or the disposer itself, and run the disposer to clear it.
Step 5: the pump
If the filter, hose, high loop, air gap and disposal are all clear and the machine still will not drain, the problem is at the pump. From here, the checks are not owner tasks on most Whirlpool built-ins — the pump sits under the tub, behind the toe panel, in water and near wiring.
What you can safely establish:
- Does the pump make any sound during the drain phase? A hum with no water movement suggests a jammed impeller. No sound at all suggests an electrical or control problem.
- Is the water level in the tub falling at all? Slow fall means partial restriction; no fall with pump noise means a jam.
- Did the problem start after any under-sink work, a disposal replacement, or a move? That points back to routing, not the pump.
If you are not comfortable with the panel off and the breaker tagged, stop here. Whirlpool’s guidance is to schedule service when draining does not improve after the filter and hose checks, and immediately if you see damaged wiring, smell burning, or the breaker trips repeatedly.
F9E1 and the power cycle
F9E1 is Whirlpool’s long drain code: the control expected the tub to empty within a set time and it did not. Whirlpool’s published steps are the same path described above, in the same order — clean the filter, check the drain hose for kinks, pinches or clogs, clear the disposer and confirm the knockout plug was removed, clear the air gap — followed by a power cycle.
The power cycle is specific: disconnect the machine from power for 30 seconds. Unplug it if it has a cord; for hard-wired units, switch the breaker off for 30 seconds and back on. Shorter interruptions may not clear the control’s memory.
Then check for excessive suds. Dishwasher detergent does not create suds; hand dish soap does. Foam can hold the float or confuse the level sensing and will push water where it does not belong. If you see bubbles, stop the machine and let them dissipate before running it again.
Prevention that actually works
- Scrape, do not rinse. Large food particles belong in the bin, not the filter system.
- Clean the filter on the schedule in your manual — more often if you cook and wash daily. A filter cleaned routinely is the single best predictor of a dishwasher that drains.
- Re-check the high loop after any under-sink work or disposal replacement. It is a two-minute check that prevents months off grief.
- Clean the air gap cap occasionally if you have one.
- Run hot water at the sink before starting a cycle so the dishwasher fills with hot water rather than cold, which helps dissolve grease and improves both wash and drain performance.
Safety notes
- Breaker off, water off, then tools out. Confirm the display and lights are dark; do not trust the panel’s off state.
- Never use drain chemicals in a dishwasher.
- Watch for damaged wiring behind the toe panel. If you see scorching, exposed conductors or water on a connector, close it up and call service.
- Hard-wired units: if you are not comfortable at the breaker panel, this is a service job from Step 5 onward.
- Water damage: a dishwasher that has overflowed repeatedly can rot the cabinet base. Check for soft board and staining under the unit after a repair.
- Hot water: the tub and the drained water can be hot. Let the machine cool before bailing it out.
Sources
- Whirlpool Product Help — Dishwasher not draining: how to diagnose and fix
- Whirlpool Product Help — F9E1, dishwasher (long drain)
- Whirlpool Product Help — Not draining / water remains at end of cycle
- Whirlpool Product Help — Not draining, newly installed
- Whirlpool Product Help — Drain line installation
For the WDT750SAKZ specifically, see our guides to its cycles and options and its cutout dimensions and door-open depth.
Frequently asked questions
Why is there always a little water in the bottom after a cycle?
If it is water in the filter well, about halfway up, Whirlpool says that is normal — it keeps the seals from drying out and is exchanged when the next cycle starts. Water across the tub floor is a different matter.
My dishwasher is new and has never drained properly. What is the most likely cause?
The disposal knockout plug. If the dishwasher drains into a garbage disposal that was installed or replaced around the same time, check the inlet: a pencil should slide in about three inches if the plug has been removed.
Does a high loop really matter?
Yes. Without it, dirty sink water can siphon back into the dishwasher and the tub will not empty fully. Whirlpool treats the high loop as a requirement, not an optional extra, and it is often lost when a disposal is replaced.
The air gap spits water onto the sink during drain. What does that mean?
That the blockage is downstream of the air gap — the hose between the air gap and the drain, or the sink plumbing itself — rather than inside the dishwasher. Clear that section and re-test.
Can I ignore F9E1 if the dishes still look clean?
F9E1 means water was left behind. Dirty water sitting in the tub grows odours and can back up onto the floor at the next fill. Treat it as a drain restriction and work the list; a power cycle alone rarely fixes it.