Bosch Dishwasher E15 or E3100: Water in the Base, What to Do

The short answer: On a Bosch dishwasher, E15 (and the display variant E3100) means the safety switch has detected water in the base of the dishwasher — Bosch calls this the leakage protection system activating. It is not a “clean the filter” code and it is not a code you clear with a button combination. Bosch’s own instruction is to turn off the water inflow and contact Bosch Customer Support at 1-800-944-2904. What you can usefully do at home is stop the water, cut the power safely, absorb what you can see, and check the hoses for kinks or visible damage, so that the technician who arrives starts from a known state instead of a machine that has been cycling with water in its base.

This guide collects what Bosch publishes about E15 and the neighbouring codes, separates the codes a careful owner can act on from the ones Bosch sends straight to service, and explains what information to have ready before you call. Where we reorder Bosch’s steps or add a practical note, we say so; the underlying definitions are Bosch’s, not ours.

In this guide

What E15 actually means

A Bosch dishwasher with this leak-protection system has a shallow base pan under the tub. A float switch sits in that pan. If enough water collects there — from a slow drip that has run for weeks, from a hose that has worked loose, or from a single event such as a fill fault — the float lifts, the switch closes, and the machine stops and reports E15. Bosch’s wording is consistent across its support pages: the safety switch has detected water in the base and the leakage protection system has been activated.

Two practical consequences follow from that definition:

  • The code describes water, not a failed part. The water may come from a clamp that loosened, a door seal that has been letting water past, an over-sudsing episode, or a component inside the wash circuit. E15 tells you where the water ended up, not where it came from.
  • Clearing the code does not remove the water. Even if the display returns to normal after a power reset, the float is still sitting in a wet pan, and the next cycle will usually trip it again — sometimes after the machine has run long enough to do more damage to the floor or the cabinet base.

Some Bosch models show E3100 instead of E15, and others show flashing active lights rather than a number. Bosch’s US error-code page gives all three the same meaning and the same instruction, so treat them as one event.

Why Bosch has no self-repair steps for E15

This is the part most online guides skip. Bosch’s own dishwasher error-code page is unusually explicit for some codes and deliberately silent for others. For a blocked filter (E22) it tells you to remove the filter, wash it under running water with mild soap and a soft brush, and reinstall it. For a blocked drain pump cover (E24/E25) it walks you through removing the cover, clearing standing water and debris, and clicking it back into place. For E15 it gives no repair steps at all — only “turn off the water inflow and contact Bosch Customer Support.”

Bosch’s regional support pages add a little more: check around the base for leakage and check the hoses for visible kinks or damage; if a hose is visibly damaged, order a replacement part; if the fault is not visible or persists, Bosch advises against attempting repairs yourself and recommends booking a repair with a Bosch engineer.

That asymmetry is worth trusting. A drain-pump cover is a user-serviceable part by design. The base pan is not: reaching the float means moving the machine out of the cabinet, and the base pan sits directly under the control electronics and the wiring harness. Our reading of Bosch’s guidance is that E15 is treated as an appliance-level leak event rather than a maintenance item, and we follow that reading in this article.

The codes around E15: which ones you can fix

Owners often misread E15 as a drain problem because a neighbouring code, E22 or E24, really is a drain problem with published steps. The table below uses Bosch’s published definitions and marks who is expected to act. “Owner” means Bosch itself gives you steps; “Service” means Bosch directs you to support.

Code Bosch’s published meaning Who acts
E12, E2060 Limescale build-up in the heat pump; the dishwasher needs descaling Owner — descale, and use softening salt if the model has a water softener
E15, E3100, flashing active lights Safety switch has detected water in the base; leakage protection activated Service — turn off water inflow and contact Bosch
E16, E17 Water is not entering the dishwasher as expected; check the inlet hose for kinks or damage Owner check, then service if it returns
E18 Water level too low or water not being pumped correctly; check inlet hose and that the supply is on (Bosch quotes a 10 l/min flow rate) Owner check, then service
E21 Heat pump blocked Service (reset power to the breaker for 30 seconds first)
E22 Filter blocked; also drain-pump cover loose, drain-pump hose kinked, or air gap / drain hose clogged Owner — clean filter, drain pump cover, hose, air gap
E23 Drain pump blocked, clogged or faulty Owner check, then service
E24, E25 Drain pump blocked or drain-pump cover loose; drain-pump hose kinked; air gap or drain hose clogged Owner — remove pump cover, clear debris, reseat until it clicks
E27 House power supply to the unit too low Owner reset, then an electrician to check incoming voltage
E07, E10, E2120 CrystalDry (Zeolite) fan motor or chamber heater fault Service
E01, E02, E03, E04, E05, E06, E09, E19, E20 Control board, relay, heater or dispenser solenoid faults Service (Bosch suggests a 30-second breaker reset first)

Note how many of these codes Bosch answers with “reset power to the breaker for 30 seconds.” That is a real instruction, but it is a diagnostic reset, not a repair: if the code comes back, the fault is still present. The same logic applies to E15 — except that Bosch does not offer the reset as a path to normal operation, because water in the base does not drain away on its own.

First hour: what to do safely

Work in this order. The sequence matters more than speed, because water plus 120 V electronics is the actual hazard here.

  1. Stop the water. Close the supply valve under the sink, usually on the hot line feeding the dishwasher. Bosch’s instruction begins here for a reason: with the valve open, a failed inlet connection keeps adding water to the problem while you are reading about it.
  2. Cut the power at the breaker, not just the panel. Bosch’s reset instructions also rely on the breaker for hard-wired units, so you will need it anyway. A dishwasher on a GFCI that has already tripped is telling you something — leave it off.
  3. Pull the machine’s front clearance and absorb what you can see. Towels at the toe kick and along the cabinet edges. If water is standing under the unit or has reached the flooring, keep people off the wet area and consider whether the floor covering needs to come up for drying.
  4. Do not tip the dishwasher. Installers sometimes tilt a unit to drain it. With water already in the base, tilting moves that water toward the electronics and the insulation, and it can turn a service call into a control-board replacement. Leave it level.
  5. Check only what is visible. Look at the inlet hose and the drain hose where they enter the cabinet for kinks, crushing, or obvious damage. Do not remove the outer door panel or the toe panel to inspect the base yourself if the unit is hard-wired.
  6. Write down the conditions. When the code appeared (mid-cycle, at the end of a cycle, or when the machine was switched on), whether it followed a move or a new installation, whether you recently changed detergent, and whether the machine had been running unusually long. A technician will ask; notes save a second visit.

If you want the dishwasher empty rather than holding a tub of water, Bosch’s published reset procedure is: press and hold the Reset (or Start) button for about 4 seconds, let the machine pump out — Bosch says this takes about a minute — then open the door and press the power button. That drains the tub. It does nothing for the base pan, so do not treat a successful pump-out as evidence that the E15 event is over.

Where the water usually comes from

Technicians find the same handful of sources again and again. None of this replaces a diagnosis, but knowing the list helps you describe the symptom accurately — and helps you rule out the causes that are really use-and-care issues rather than failures.

Likely source Typical clue Owner action
Excess suds from hand dish soap or too much detergent Foam visible in the tub when you open the door; drips at the door corners Use only automatic dishwasher detergent; let suds dissipate; run a rinse once the base is dry
Door seal letting water past Water tracks down the inside of the door; moisture along the cabinet edge Clean the seal; check for food or a warped gasket; service if damaged
Loose or cross-threaded inlet connection Recent installation or a machine that was pulled out for cleaning Do not re-tighten blindly; have the connection checked
Drain hose or air gap problem Water backing up at the sink; a gurgling drain; a hose without a high loop Check the high loop and air gap (see our Whirlpool drain guide for the same parts)
Internal component leak (pump seal, sump, heat pump circuit) No visible cause; code returns without a completed cycle Service only

Two of those rows are worth acting on before a technician arrives, because they change the diagnosis. Suds are common in households that switched from pods to gel, or that rinsed a greasy pan with dish soap and loaded it wet. A missing high loop is common after a disposal replacement. Both produce water in the base without any failed part, and both are cheaper to fix than a pump.

What to have ready before you call

Bosch’s support pages ask you to identify the appliance before booking. The two numbers that matter are printed on the rating plate, usually on the inner edge of the door or the door frame:

  • E-Nr — the model number, including the version suffix. Two dishwashers that look identical can use different pumps.
  • FD — the production number, which encodes the manufacturing date and is how parts are matched.

Have those, the purchase date, and your notes from step 6 above. If the machine is inside a warranty period, ask whether the visit is covered before authorising work, and say plainly that the code is E15 with water in the base — some call centres route leak codes to a different queue than electrical codes.

Repair or replace: how to think about it

E15 is one of the few codes where the repair cost is genuinely unknown until someone looks, because the same code can mean a $2 clamp or a failed wash pump. Rather than guessing at prices, ask the technician for a diagnosis before authorising the repair, and compare three numbers: the diagnostic fee, the quoted repair, and the cost of a comparable new unit installed. A useful rule of thumb many owners apply is to repair when the quote is comfortably under half the replacement cost and the machine is otherwise healthy. That rule is our suggestion, not Bosch’s.

Also weigh what the leak touched. A machine that leaked onto a wood subfloor or into a cabinet base has a second bill coming for drying and repair, and a repeat leak in the same spot is a strong argument for replacement.

Safety notes

  • Water and electricity: never open the door panel, the toe panel, or the base of a machine that is still connected to power. Confirm the breaker is off, not just the control panel.
  • Flood risk: if the supply valve will not close fully, shut off the house water and call a plumber before the appliance technician.
  • Do not bypass the float switch. It exists to stop the machine when water is where it should not be; a bypassed switch turns a leak into a flood.
  • Do not use drain-cleaning chemicals in a dishwasher to “clear” a leak — they attack seals and make the leak worse.
  • Repeated breaker trips or a burning smell mean stop, unplug if possible, and call service. Do not reset a third time.
  • Mould and flooring: water that sat under a cabinet for days can damage particleboard and grow mould. Dry the area, and check the cabinet base after the repair.

Sources

For drying behaviour on Bosch’s CrystalDry models, see our SHP78CM5N not-drying guide, and for program selection see SHP78CM5N cycles and Home Connect.

Frequently asked questions

Can I just reset E15 and keep using the dishwasher?

You can clear the display, but Bosch does not present that as a fix. E15 means water is sitting in the base pan. Resetting power may let the machine start, and the float switch will usually trip again once more water collects — meanwhile the leak continues. Bosch’s instruction is to turn off the water inflow and contact support.

Is E3100 the same as E15?

Yes, on Bosch’s US error-code page E3100 carries the same definition as E15: the safety switch has detected water in the base and the leakage protection system has activated. Some models show flashing active lights instead of a number, with the same meaning.

Does E15 always mean a part has failed?

No. Water in the base can come from over-sudsing with hand dish soap, a door seal that let water past, or a drain hose without a proper high loop. Those are installation and use issues rather than failed components — but the base still has to be dried and inspected, which is why Bosch routes the code to service rather than to a self-repair routine.

Can I dry the base myself and run it again?

Bosch advises against attempting repairs yourself when the fault is not visible or persists, and reaching the base means moving the machine and working under the electronics. If you have dried the visible water and the code returns on the next start, that is your answer: the source is internal and needs a technician.

What should I tell Bosch when I call?

Give the E-Nr and FD numbers from the rating plate, say the display shows E15 (or E3100), describe when it appeared, and mention anything you changed recently — a new installation, a disposal replacement, a detergent change, or a machine that was moved for floor work. That single sentence often decides whether the visit is a hose job or a pump job.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *