LG Refrigerator Er FF and Er rF: The Defrost That Clears It

The short answer: On an LG refrigerator, Er FF (also shown as E FF or just F) means the freezer fan motor is not turning; Er rF means the same for the refrigerator compartment fan. The usual cause is not a dead motor but ice or frost around the fan, and LG’s published fix is a genuine defrost: move the food out, put towels down, unplug the refrigerator and leave both doors fully open for at least 24 hours, dry the interior, then plug it back in and allow 24 to 48 hours for the compartments to reach temperature. LG notes that the thaw can take about a day in summer and up to three days in winter, depending on how much ice there is. If the code is still there after a complete defrost, it is a service call — LG says the same code repeating means a technician should inspect it.

For a quick reset first, LG’s other instruction is to unplug the unit (or trip its dedicated breaker), wait about five minutes, and power it back on. If the code clears and stays clear, the fault was transient. If it returns, go to the defrost.

In this guide

Why a fan code is really an ice code

A modern refrigerator moves cold air with fans. One fan pushes air across the evaporator in the freezer; another circulates it in the fresh-food compartment, or through a duct between the two. If ice forms around a fan blade, the blade cannot turn, the motor’s feedback stops, and the control reports FF or rF.

The ice does not appear for no reason. LG names the two conditions it sees most:

  • The freezer is too full, so a package sits against the fan or blocks the air path, and moisture condenses and freezes in place.
  • The door is not fully closed, letting humid room air in. Every opening cycle brings in more moisture; the freezer’s job is to remove it, and it ends up as frost on the coldest surface — often the fan shroud.

That is why the defrost is the fix and the reset is only a test. A reset restarts the motor; it does not melt the ice. Within a day or two the fan stalls again, which is exactly the pattern LG describes when it says a repeating code needs a technician.

The LG defrost procedure, step by step

LG publishes this sequence for both Er FF and Er rF. Follow the order; the first two steps exist to protect your food and your floor.

  1. Move the food. To another refrigerator, or to insulated coolers with ice. A 24-hour defrost is long enough that nothing perishable should stay inside.
  2. Put dry towels on the floor around the refrigerator, and inside along the bottom if you can. The melt water has to go somewhere, and the defrost drain can be partly iced over — which is sometimes the original problem.
  3. Unplug the refrigerator and leave both doors fully open for at least 24 hours to let the ice and frost melt naturally. LG’s guide puts the range at about one day in summer and up to three days in winter, depending on how much ice has built up.
  4. Dry the interior with a dry towel once the ice has completely melted.
  5. Plug the refrigerator back in and allow 24 to 48 hours for both compartments to reach their normal operating temperatures before you judge the result or reload all the food.
  6. If the code returns after a complete defrost, request service. LG states that a repeating code needs an LG technician for an accurate diagnosis.

Two practical notes that the published steps leave implicit:

  • Do not use a hairdryer, a heat gun, or a knife. Heat warps liners; a knife punctures the evaporator, which turns a defrost into a sealed-system repair. Air temperature and time are the tools here.
  • Watch the defrost drain while it melts. If water pools in the bottom of the freezer instead of draining away, the drain is blocked by ice or debris, and that blocked drain is likely what flooded the fan in the first place. Clear it once the ice is soft, and tell the technician if it re-freezes.

Both notes are our guidance rather than LG’s text, but they are the difference between a defrost that holds and one that repeats next month.

The rest of LG’s code list

LG’s published code list is longer than most owners expect, and much of it maps one-to-one onto a component. The codes below are quoted from LG’s digital-display code page. LG’s own summary for the malfunction group is blunt: for the following error codes, please request service.

Code LG’s stated meaning Owner action
FF Freezer fan fault — this fan circulates cold air through the freezer; if blocked, the compressor overworks and performance drops Defrost as above; service if it returns
rF Refrigerator compartment fan fault Reset about 5 minutes; service if it repeats
CF Condenser fan fault — the fan that cools the condenser Service
CO Communication error between the main board and the display Service
FS Freezer temperature sensor fault Service
FU Cycle error: ten minutes after start the freezer has not dropped below 3.5°C, or it has risen above 3.5°C during operation Published checklist — see below
IF Ice maker fan fault — the fan moving cold air from the freezer to the ice maker Service
IS Ice maker temperature sensor fault; ice making may stop Service
It Ice maker motor fault Service
rS Refrigerator sensor fault (R1, upper part) Service
dS Defrost sensor fault; the evaporator may become blocked by ice Service
rT Ambient temperature sensor fault Service
dH (or FdH, dHF) Defrost resistance issue: the defrost sensor has not risen more than 5°C within 80 minutes of defrost starting Service
SS Water tank temperature sensing issue Service
gF Water flow sensor fault — closed tap, kinked hose, or incorrect water pressure Check the tap and hose, reset, then service
CH Refrigerant leak, high-pressure side (appears when temperature and compressor sensors show abnormal values) Service — stop using
CL Refrigerant leak, lower side Service — stop using

The two leak codes deserve emphasis. CH and CL mean the sealed system has lost refrigerant, and LG’s page is unambiguous that service is required. Running a refrigerator with a refrigerant leak does not restore cooling, and on some models it can damage the compressor while you wait.

The gF code is the one owner-fixable item in the malfunction group, because its trigger is often outside the machine. LG’s steps: unplug, wait 60 seconds, plug back in directly into a wall outlet without a power strip or multi-socket, wait up to 5 minutes for the appliance to restart and monitor its components, then make sure the water tap is fully open, the hose is not kinked, and the pressure is within the range stated in your manual.

Codes that are warnings, not faults

Three displays on LG refrigerators are information rather than failure:

  • Lo — the ambient temperature around the refrigerator has dropped below -10°C. LG notes the appliance will not function optimally in such low temperatures. That is a room problem, not a refrigerator problem.
  • HI — the ambient temperature has risen above +50°C, with the same caveat.
  • Demo / display mode — a showroom setting that disables all cooling in both compartments. See below.

A garage refrigerator in a cold climate can produce Lo every winter, and no amount of service will fix it. The answer is a location that stays within the operating range.

FU: the one code with a real checklist

FU is LG’s cycle error, and LG gives it a genuine owner checklist rather than a single instruction. The code appears when the freezer has not reached 3.5°C within ten minutes of starting, or has risen above 3.5°C while running.

  1. Unplug the refrigerator, wait 60 seconds, plug it back in — into a direct outlet, not a power strip or multi-socket.
  2. Confirm the refrigerator is on and that the compressor is running and both cooling and freezing temperatures are in normal ranges.
  3. Check the freezer setting. LG’s reference setting is -18°C; a setting that drifted warm will produce exactly this code.
  4. Review door habits. How often and how long the door is opened. Opening lets warm, humid air in, and the longer it stays open the more cooling performance drops.
  5. Look for food blocking the air vents. Blocked vents stop cold air reaching the compartment.
  6. Check that the door closes properly and the gaskets seal. LG’s test: put a piece of paper between the door and the cabinet, close the door, and pull. It should resist. If it slides out easily, the seal is not sealing.
  7. Check the door bins. If food in the door bins is hit by extreme temperatures, the door insulation may be at fault.

That last item is a useful distinction. A cold spot in a door bin is a different fault from a warm compartment, and the checklist separates them.

Demo mode

LG’s demo mode disables cooling in both compartments so a showroom unit can run its display. Two methods are published, and models differ:

  • Open the refrigerator-side door, hold the FRIDGE button and press Express FRZ three times; or
  • Hold FRIDGE and Express FRZ together for about 3 seconds.

A sound confirms the setting has been deactivated. If you have just taken delivery of a floor model and nothing gets cold, check this before calling anyone.

LG also publishes a way to force a code to display when you suspect one was cleared by a power failure: press and hold the Freezer Temperature and Express Frz buttons together for at least 3 seconds.

What to do with the food during a defrost

A 24-to-72-hour defrost is a real interruption, so plan it like one:

  • Coolers with ice packs hold a refrigerator’s worth of food for about a day if you keep them closed and out of the sun. Fill the coolers tight; the ice lasts longer.
  • Group items by when you will use them. Anything you plan to cook in the next 24 hours can go to the front of the cooler and be used first.
  • Check food safety rules before you reload. The USDA advises that refrigerated food held above 40°F for more than two hours should be discarded, and that a full freezer keeps food safe for about 48 hours if the door stays closed. Use a thermometer rather than your hand.
  • Do not restock a warm refrigerator. Let it pull down to temperature empty first, then reload — otherwise the compressor runs flat out with a full load of warm food, which is how a fan code turns into a compressor problem.

Safety notes

  • Do not disassemble the refrigerator or replace internal parts yourself. LG’s warning is explicit: doing so may cause fire, electric shock, serious injury or death.
  • Unplug before cleaning or drying the interior, and keep the cord out of the melt water.
  • If the code persists, stop using the refrigerator and contact LG Support for service.
  • Never chip ice off the evaporator, and never use sharp tools to clear a fan.
  • Refrigerant: CH and CL mean a sealed-system leak. Do not attempt to top up or repair it yourself.
  • Give the unit room. LG asks for at least 2 inches behind the refrigerator, and recommends vacuuming the condenser cover rather than removing it.

Sources

For the same symptom on other brands, see our warm fridge, cold freezer guide and the Samsung error-code reference.

Frequently asked questions

Does Er FF mean the fan motor is broken?

Not necessarily. LG attributes it most often to ice or frost building up around the fan and stopping it from turning. That is why the published fix is a full defrost rather than a part. If the code returns after a complete 24-hour defrost, then the motor or its feedback circuit is the suspect.

How long does LG’s defrost actually take?

At least 24 hours with both doors open, according to LG. It adds that the melt can take about a day in summer and up to three days in winter, depending on how much ice has accumulated, and that the compartments then need 24 to 48 hours to reach normal temperature.

Can I just reset and keep using it?

You can, and it may run for a day or two. But the ice is still there, the fan will stall again, and each cycle runs the compressor harder. A reset is a diagnostic step, not a repair.

What is the difference between Er FF and Er rF?

FF is the freezer compartment’s fan motor; rF is the fresh-food compartment’s fan motor. LG’s published defrost procedure is the same for both, and the same rule applies: if it repeats after defrosting, request service.

My display shows Lo. Is the refrigerator failing?

No. Lo is a warning that the room has dropped below -10°C, where the appliance cannot work optimally. Move it somewhere warmer rather than booking service.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *