Samsung WF45T6000AW Error Codes: 4C, 5C, 1C, dC and How to Clear Them
The short answer: A Samsung front-load washer such as the WF45T6000AW shows information codes rather than a service light, and almost every one of them names a system you can test yourself. 4C means water is not getting in, 5C means it is not getting out, 1C and LC relate to the water level sensor or a leak, dC is the door, UE is an unbalanced load, and 9C1 or 9C2 point to the power supply rather than the washer. Samsung groups these in its washing machine information and error codes guide, and this article follows the same order of causes so you can clear the common ones before booking a technician.
In this guide
- How to read a Samsung information code
- The full code table
- 4C: not filling
- 5C: not draining
- 1C and LC: water level or leakage
- dC: the door
- UE and Ur: unbalanced load
- 9C1, 9C2 and PF: power supply
- 3C: motor
- Routine work that prevents most codes
- Safety before you start
- When a code means call Samsung
- Frequently asked questions
How to read a Samsung information code
Samsung designs these displays to be read, not feared. A code appears in place of the remaining time, the machine beeps, and the cycle stops or pauses depending on what failed. Three habits make the code useful:
- Note whether the cycle was filling, washing, draining, or spinning. The same code at a different point in the cycle shortens the list of causes.
- Expect the panel to lock out for a few minutes on some codes. Samsung notes that when the washer displays 4C or 1C it drains for about three minutes and the power button does not respond during that time. That is normal behavior, not a second fault.
- Reset once, then observe. Unplug the washer or switch its breaker off for about a minute, restore power, and run a short cycle. A code that survives a reset with a normal load is a real fault; a code that appears once after a plumbing repair is usually installation.
One quirk is worth knowing before you compare codes online. On some Samsung models dC is a door error and on others it is an unbalanced-load error, and 3E can be a motor error or a voltage error depending on the model. Samsung says this explicitly and points owners to the manual for the model in question, which is why the table below marks those two codes as model-dependent.
The full code table
| Code | System reported | First check | Do it yourself? |
|---|---|---|---|
| 4C (also 4E, nF) | Not filling | Taps open, hoses not kinked, hot and cold connected to the right inlets, inlet screens clean | Yes |
| 5C (also 5E, nd) | Not draining | Drain hose kinked or frozen, debris filter clogged, drain hose position | Yes, for hose and filter |
| 1C (also 1E) | Water level sensor | Whether the washer finished filling, evidence of suds | Partly |
| LC (also LC1) | Water level or leakage | Water under the machine, kinked hoses, excessive detergent | Partly |
| dC (also dE, dL) | Door | Door shut, nothing caught in the gasket, child lock off | Yes |
| UE (also Ub, U6) | Unbalanced load | Load distribution, one heavy item, small load | Yes |
| Ur | Unbalanced load retry — the washer is correcting itself | Nothing; the cycle will take longer | No action needed |
| 9C1 / 9C2 (also 9E1, 9E2, PF) | Voltage supply | Dedicated circuit, no extension cord, breaker not tripped | Yes |
| 3C (also 3E) | Motor — but 3E is voltage on some models | Restart the cycle; check the manual for the model | Restart only |
| AC6 | Communication between control boards | Restart the cycle once | Restart only |
4C: not filling
4C is the code you will see after moving the washer, after plumbing work, or in the first cold week of winter. Samsung’s checklist is worth following in order because each item is cheap to check:
- Confirm the hot and cold hoses are on the correct inlets. Samsung warns that if you do not connect the hot water line at all, the washer will throw an error the first time it wants hot water — which can happen even on cycles labeled Cold. A washer that fills and then stops after a few minutes is a classic sign of a missing or swapped hot line.
- Open both valves completely and leave them open while the washer runs. Half-open valves deliver enough water to start and not enough to finish.
- Check hose routing. Look for bends behind the machine and confirm the drain hose is inserted between 6 and 8 inches into the standpipe. Samsung notes that the drain hose must not be pushed in deeper, and that the screw holding the drain hose bracket at the back of the washer should stay in place.
- Clean the inlet screens. Turn the water off, unscrew the hoses from the back of the washer, and look at the small mesh filters inside the inlets. Grit and scale there restrict flow, especially on the hot side in hard-water areas.
- Power cycle for one minute. Samsung recommends unplugging the washer or flipping its breaker for a minute before retrying, which clears a control that latched the error.
One product-specific caution from Samsung’s guide: do not use Flood Safe hoses on this washer. Those hoses contain a shutoff device that can trigger during a normal fill and produce repeated 4C errors that look like a machine fault.
5C: not draining
5C means the washer cannot empty the drum, so the cycle stops with water still in it. The two usual causes are a blocked path and a blocked filter.
- Straighten the drain hose. A hose pinched behind the machine, or one whose end is sitting in water in a laundry sink, will not drain or will siphon. Pull the machine out far enough to see the whole hose run.
- Clear the debris filter. On this front-load series the pump filter sits behind the small access door at the bottom front. Drain the residual water into a shallow pan first — the trapped water is often a gallon or more — then unscrew the filter and remove lint, coins, hair pins and anything else caught in the impeller housing. Our WF45T6000AW Self Clean and pump filter guide walks through the drain-and-clean sequence in detail, including how to avoid a flood on the laundry floor.
- Check for ice in winter. A drain hose that runs through a garage or along an exterior wall can freeze solid. Thaw it before running another cycle.
If the hose is clear and the filter has been cleaned and 5C returns on an empty rinse-and-spin, the drain pump itself is the likely fault, and that is a service part.
1C and LC: water level or leakage
Samsung groups these because both depend on the pressure sensor that tells the control how much water is in the drum. 1C reports a problem with the water level sensor itself; LC reports that moisture was detected where it does not belong, or that the sensor cannot read correctly.
Start by looking for water. Pull the washer out, shine a light under the front edge, and check the floor and the base pan. Even a slow seep from a loose hose clamp shows up as a damp patch or a mineral stain and explains an LC code that appears days apart. If you find a leak, fix the connection — the code is a symptom.
If the machine is dry, check for suds. Excess detergent or a non-HE detergent creates a foam layer that the pressure sensor reads as a full drum, and the washer then either stops filling or overfills. Samsung’s test is simple: run an empty cycle with no detergent and watch through the door glass. Visible suds mean detergent is the cause. Run empty cycles until the foam stops, then reduce your dose.
Finally, check that the hoses behind the machine are not kinked, and that the drain hose bracket screw is in place. A drain hose that has come loose from its holder can spray inside the cabinet and trigger LC.
dC: the door
dC means the washer does not detect a closed, locked door. Close the door firmly, then check the fold of the rubber gasket for a sock, a washcloth, or a bra strap that is holding the door open by a few millimeters. Look at the latch on the door edge for cracks.
Two conditions produce this code without any mechanical fault. If child lock is on, opening the door can trigger the message even when the washer is idle. And on some models dC is not a door code at all but an unbalanced-load code, so if the drum is visibly loaded to one side, redistribute before assuming a latch problem. Samsung’s reset for a door code is to unplug the machine, check the latch area, then restore power and start again. A code that returns with a clean gasket, an even load, and child lock off means the door switch or lock assembly needs service.
UE and Ur: unbalanced load
UE stops the cycle because the drum cannot spin safely. Ur is a different message with the same root: the washer is going to add water, redistribute the load, and try the spin again, which makes the cycle longer but does not indicate a fault. Samsung states plainly that a Ur code is not a problem with the machine.
For UE, open the door and spread the load around the drum. One heavy item — a bath mat, a single pair of jeans, a small blanket — is the usual culprit. If the load is very small, add one or two towels so the drum has something to balance against. Large comforters belong in a bulky cycle, and if a comforter keeps failing, wash it in a commercial machine. If UE appears with ordinary mixed loads, check that the washer is level: rock it corner to corner, and adjust the leveling feet until it sits flat with all four feet carrying weight.
9C1, 9C2 and PF: power supply
These are voltage codes, not washer codes. Samsung’s guidance is that the washer should be on its own circuit, without an extension cord, and that electric models need the correct power cord installation for the household supply. PF appears after an actual power interruption — an outage, an unplugged cord, or a tripped breaker.
Practical checks: confirm the washer’s plug is fully seated, look at the breaker panel for a tripped breaker (switch it fully off, then on), and remove any extension cord or power strip from the path. If 9C1 or 9C2 returns on a dedicated circuit with no outage, the control is reporting a supply problem it cannot fix, and an electrician should look at the circuit before the washer is blamed.
3C: motor
3C points at the motor or its drive. Start the cycle again once — an intermittent 3C after a very heavy load often clears. Do not keep retrying a washer that repeats 3C with a light load: a binding drum or a failing drive will damage more parts each time it runs. Check first that the drum turns by hand with the power off, then arrange service.
Routine work that prevents most codes
- Clean the pump filter every one to three months, or any time a cycle ends with standing water.
- Run the Self Clean cycle monthly or as the panel prompts, and wipe the door gasket dry afterward. Our Self Clean+ and pump filter guide covers how the cycle differs from cleaning the filter.
- Use HE detergent in the measured amount. Suds cause a large share of 1C, LC and FE-type complaints.
- Leave the door ajar between loads so the gasket and drum dry, which prevents the mold that leads to odor complaints and gasket damage.
- Check the inlet screens once a year if your water is hard.
If a cycle seems to run in an unexpected order or stops at an odd point, the settings may simply not be what you think. Our WF45T6000AW cycles and settings guide explains what each control actually changes, and the dimensions guide covers door clearance and stacking if you are planning to move the machine to reach a hose.
Safety before you start
- Unplug the washer or switch its breaker off before touching hoses, the filter, or the drum.
- Expect hot water at the filter and the residual hose if the machine stopped during a warm wash.
- Never run the washer with the door switch bypassed, and never tape the door closed to defeat a lock error.
- Do not use the washer if water is pooling on the floor; unplug it and deal with the leak first.
- Keep the area around the machine dry while you work so you are not standing in water at a plugged-in appliance.
When a code means call Samsung
Contact service when a code returns after one full round of the checks above, when you find water leaking from inside the cabinet rather than from a loose hose, when the drum will not turn by hand, when the panel is unresponsive after a breaker reset, or when you smell burning. Those conditions describe a failed pump, sensor, lock, motor or control board — parts that need a technician who can also confirm the machine is safe.
Frequently asked questions
Why did the power button stop working when 4C or 1C appeared?
That is designed behavior. Samsung states that on these codes the washer drains for about three minutes and the power button is inoperative during that time. Wait for the drain to finish, then reset the machine.
Can I clear a code by unplugging the washer?
Unplugging or switching the breaker off for about a minute clears the latched message and is the standard first step. It does not fix a blocked hose or filter, so a code that returns immediately means the physical cause is still there.
Is a Ur code a fault?
No. Ur means the washer is retrying the spin after detecting an unbalanced load. The cycle gets longer, and the load may need rearranging, but nothing is broken.
Why does my washer show 4C only on some cycles?
Because it only needs hot water on some steps. A disconnected or restricted hot line causes an error the first time the cycle calls for warm or hot water, which can be well into a cycle that started cold. Check the hot hose and its inlet screen rather than the machine’s electronics.
Does the pump filter need to be cleaned even if I never see 5C?
Yes. Lint, hair and small objects collect steadily, and a partly clogged filter shows up first as longer cycles and damp clothes before it produces a code. A quarterly clean is the simplest prevention.
What if the code is not listed here?
Samsung’s support pages list codes by product family and model, and the same letters can mean different things on different machines. Check the model-specific page or the manual for the WF45T6000AW before acting on a meaning you found for another washer.