Whirlpool WTW5057LW Error Codes: drn, F9E1, LdL and What to Check First

The short answer: A Whirlpool top-load washer such as the WTW5057LW reports most problems with a short word rather than a number, and the words are unusually literal. drn and F9E1 mean the machine is not draining, LF or F8 E1 means it is taking too long to fill, LdL and LdU are lid-lock messages, Ofb means the load is out of balance, OL means it is too large, and Sud means there is too much detergent foam. Whirlpool publishes this list for its HE top-load washers in its error codes reference, and most of the fixes below take less than fifteen minutes.

In this guide

What the display and the flashing lights mean

Not every WTW5057LW configuration shows letters. Models with a digital display print the code; models without one communicate by flashing the cycle lights, and the pattern is read the same way — a count of flashes corresponds to the code letter. Whirlpool’s reference points owners to the model’s Use and Care guide for the exact code set, because the list can differ slightly between models in the same family.

Two display behaviors are normal and easy to mistake for faults:

  • A code that clears when you press Start/Pause was a condition the control detected once — a lid opened mid-cycle, a brief power dip. If it does not return during the same cycle, nothing needs repair.
  • A code that appears and then disappears while the washer keeps working is often the load-balance or suds routine correcting itself, which is what “Ofb” and “Sud” are designed to report.

The full code table

Code What Whirlpool reports First check Self-fixable?
drn Washer is not draining properly Drain hose kinked, crushed, or pushed too far into the standpipe Usually yes
F9E1 Long drain Drain hose depth in the standpipe, kinks, blockage in the drainpipe Usually yes
LF, Lo FL, F8 E1 Washer is taking too long to fill Both taps open, inlet screens clean, water pressure Yes
HC Hot and cold inlet hoses installed reversed Which hose feeds which inlet at the back Yes — swap them
LdL Lid is not locking Items under the lid, detergent buildup around the lock Yes, for obstructions
LdU Lid cannot unlock Objects resting on top of the lid, such as a laundry basket Yes
lid The lid was left open Close the lid; the cycle resets after 10 minutes Yes
F5E2 The washer cannot engage the lid lock Obstruction in the lid-lock area Yes, for obstructions
Ofb Load is out of balance How items are arranged around the washplate Yes
OL Load was too large Water level and how full the basket is Yes — remove items
Sud Excessive suds Detergent type and amount Yes
PF Cycle interrupted by a power failure Outlet, breaker, outage Yes
F# E# or F## System error code Press Start/Pause to clear, then restart Reset first, then service

Drain problems: drn and F9E1

Both messages say the same thing: water is leaving the drum too slowly. Whirlpool notes that this is often an installation problem rather than a part failure, which is why the hose checks come first.

  1. Check how far the drain hose goes into the standpipe. Whirlpool warns against pushing the hose down past the elbow. When the hose end sits deep in the pipe, it can siphon: water drains partly, then flows back, and the machine reads a slow or incomplete drain. The manufacturer-supplied hose form is correct as it comes, and it should not be altered or taped to the pipe.
  2. Straighten the hose. Look for a kink where the hose exits the machine and where it bends into the wall or laundry tub.
  3. Clear the drainpipe or utility sink. A slow household drain looks exactly like a slow washer. Pour a bucket of water into the standpipe and see how fast it goes down.
  4. Clear lint from the drain path where your model gives access. Many top-load washers of this type do not provide an owner-accessible pump filter at all, so a persistent drn with a clear hose points to the pump.

If the hose is at the right depth, the pipe is clear, and a spin-only cycle still produces drn or F9E1, the drain pump is the likely fault.

Fill problems: LF, Lo FL, F8 E1 and HC

A top-load washer that cannot fill in a reasonable time reports LF, Lo FL or F8 E1. Whirlpool’s own list treats these as one message with several spellings, and the cause is almost always on the plumbing side.

  • Open both faucets completely. This machine needs both hot and cold supply; Whirlpool states that both must be supplied for a proper fill.
  • Clean the inlet screens. Shut the water off, disconnect each hose at the washer, and rinse the mesh screens. Scale on the hot screen is the usual reason a washer fills slowly only on warm cycles.
  • Check the pressure. If a nearby faucet is weak too, the house supply is the problem, not the washer.
  • Look for a pinched hose where the machine was pushed back against the wall after installation.

HC is a different kind of fill message: it appears at the end of a wash and tells you the hot and cold hoses are connected to the wrong inlets. Whirlpool’s fix is to turn the water off, swap the two hoses, and run another cycle to confirm. This code exists because a reversed hookup produces poor wash results that would otherwise be blamed on detergent or the machine.

Lid problems: LdL, LdU, lid and F5E2

Because a top-load washer must lock its lid before it spins, lid messages are common and rarely mean a broken lock.

  • LdL — the lid will not lock. Whirlpool’s guidance is to check for items directly under the lid and to clean detergent buildup around the lid-lock mechanism. A sock or a shirt edge caught at the rim is enough to stop the lock from traveling.
  • LdU — the lid cannot unlock. The washer detects weight or obstruction on top of the lid, so remove the laundry basket, detergent jug, or anything else resting there.
  • lid — the lid was left open. Close it to clear the message. Whirlpool warns that if the lid stays open more than 10 minutes the cycle resets and the water drains; if that has already happened, start the cycle over and do not add more detergent, because the clothes are already saturated with soapy water.
  • F5E2 — the lock cannot engage because something is in the lid-lock area. Clear the area, check for clothing in the way, then power the washer down for five minutes to reset the control.

The common thread: clear the lid area, cycle the power, and try again. A lid code that returns with a clean rim and nothing on the lid indicates a failing lock assembly, which is a service part rather than a user-replaceable one on most models.

Load and suds problems: Ofb, OL and Sud

Ofb means the washer is running its load-balance correction routine. Whirlpool’s advice is to let it continue. If the dial is flashing and the machine has stopped, redistribute the load in a loose heap around the washplate, close the lid, and press Start/Pause. Avoid washing single heavy items; balance a rug or a jacket with a few towels. For oversized, non-absorbent items such as comforters or puffer jackets, use the Bulky/Sheets cycle, because those items do not behave like normal fabric in a high-efficiency top loader.

OL means the load was too large for the water level the machine could use. The washer will drain the water and detergent it has already added, so the fix is to remove several items, add HE detergent for the smaller load, close the lid, and start again. Overloading a top-load washer is the single most common cause of both OL and Ofb.

Sud means too much foam. Whirlpool’s instruction is blunt: always use HE detergent. Regular detergent in a high-efficiency washer produces a foam layer that the machine reads as a load problem, extends the cycle, and can leave residue in the drum. If Sud appears, run a rinse and spin, reduce your dose by a third, and check that you are not also adding a booster that contains surfactants.

The cycles themselves can look like faults when they behave unexpectedly — long soak periods, extra water, or a slow finish. Our guide to Deep Water Wash, PreSoak and Quick Wash explains which options intentionally add water and time.

Power and control messages: PF and F codes

PF reports that the cycle was interrupted by a power failure. Touch and hold Start to resume, or press Power to clear the display and start again. If PF appears without a household outage, check that the washer is not sharing a circuit with a large appliance and that its plug is fully seated.

A system error appears as F followed by numbers, such as F1E1 or F5E2. Whirlpool’s instruction is to press Start/Pause once to clear the code, then press it again to restart the washer. For F1E1 specifically, the recommended reset is to disconnect the washer from power for five minutes — not five seconds — and then restore it. If the system code returns after that, Whirlpool directs owners to schedule service, because these codes describe faults the control cannot work around.

The order that saves the most time

  1. Write down the code and note when it appeared: fill, wash, drain, or spin.
  2. Press Start/Pause once to see whether the code clears by itself.
  3. Cycle the power — unplug for five minutes — then run a short cycle.
  4. Check the three plumbing points: both faucets open, hoses not kinked, drain hose at the right depth.
  5. Check the load: not overloaded, arranged evenly, HE detergent in the right dose.
  6. Check the lid area: nothing under the lid, nothing on top of it, no detergent crust around the lock.
  7. Only then call service, with the code and what you already ruled out.

Routine care for a top-load washer

  • Wipe the lid rim and the lock area monthly. Detergent film is the main cause of LdL messages that appear out of nowhere.
  • Run a cleaning cycle with a washer cleaner every month or two, following the product directions, and leave the lid open between loads so the basket dries.
  • Rinse the inlet screens once a year, more often with hard water.
  • Keep the drain hose at its factory depth in the standpipe, and do not tape or clamp it to the pipe.
  • Measure detergent. A high-efficiency top loader uses far less water, so the dose on the bottle is a maximum, not a target.

Safety before you open the lid or move the machine

  • Unplug the washer before moving it to reach hoses or the back panel.
  • Never hold the lid switch or lock closed to force a spin. The lock exists because the drum moves fast enough to injure a hand.
  • Do not stand in water while working on a plugged-in appliance; dry the floor first.
  • If you see water under the machine, stop and find the source before running another cycle.
  • Keep children away from an open washer; a top-load basket is a drowning hazard.

When to schedule service

Schedule service when a drain code survives a clear hose and a clear standpipe, when a lid code returns after clearing the rim and resetting the control, when a fill code appears with strong water pressure and clean screens, when a system code (F followed by numbers) returns after a five-minute power cycle, or when you hear grinding, smell burning, or see water inside the cabinet. Give the technician the exact code and the point in the cycle where it appeared — that single detail often decides which part they bring.

Frequently asked questions

Why does my washer show “lid” even though the lid is closed?

Check the rim for an item caught under the lid and the lock area for detergent crust. If the message appeared after the lid sat open for more than ten minutes, the cycle has already reset and drained, so you need to start a fresh cycle rather than resume the old one.

Is it safe to keep using the washer after a drn or F9E1 code?

Only after the drain path is clear. Running cycles with a restricted drain leaves water in the drum, stresses the pump, and can overflow if the machine tries to fill again. Fix the hose depth or blockage first.

What does HC actually mean?

The hot and cold hoses are plumbed backwards. Whirlpool’s own list describes HC as the cold hose connected to the hot inlet and the hot hose connected to the cold inlet, reported at the end of the cycle. Turn off the water, swap the hoses, and run a cycle to confirm.

Why do I get OL when the basket does not look that full?

Because the load is heavy or water-hungry rather than tall. A few thick towels, a heavy rug, or a comforter can exceed what the chosen water level can move. Remove several items and use a cycle intended for bulky items.

Can I reset the washer without unplugging it?

Pressing Power and then Start/Pause clears many messages, but Whirlpool’s reset instruction for control faults is a full power removal, and for F1E1 that means five minutes disconnected. Use the outlet or the breaker, not just the button.

My code is not in this list. What now?

Whirlpool’s code set varies by model, and its reference directs owners to the Use and Care guide for the exact model. Look up WTW5057LW in Whirlpool’s manual library before assuming a code from a different washer applies.

Similar Posts